Dell'Orto carburetors - Slide needle specifications
Antietam Classic Cycle - Excellent service spanning tune-ups to restorations Decals from John Prusnek - Very nicely produced decals you'll be proud to adhere Relays from Dan Prunuske - Great product, great prices Stainless Cycle - Conveniently assembled and polished stainless fastener kits Zydeco Racing - Top notch transmission & rear drive service at unbelievable pricing |
Table of contents
- Slide needle specifications for PHBE...P-VHSA carburetors (U slides)
- Slide needle specifications for PHBE-PHF-PHM-PHSB-VHSB carburetors (K slides)
- Slide needle specifications for PHBG carburetors (W slides)
- Slide needle specifications for PHBH carburetors (X slides)
- Slide needle specifications for PHBL carburetors - (D slides)
- Slide needle specifications for PHVA-PHBN carburetors - (A slides)
- Slide needle specifications for PHVB carburetors (M slides)
- Slide needle specifications for VHB carburetors - (V slides)
- Slide needle specifications for VHBZ-PHSA carburetors - (E slides)
Slide needle specifications for PHBE...P-VHSA carburetors (U slides)
This information was gleaned from eurocarb. I meticulously recreated the table of values from a difficult to read original. Therefore, mistakes may be present. Here is a link to the original image in case you would like to scrutinize any particulars.
PHBE...P-VHSA carburetor slide needle. Note the term 'cilindrico' which translates to 'cylindrical'.
Table: Slide needle series 9713 X 08 U
| Type | Value X | Characteristic expressed in millimeters | ||||
|---|---|---|---|---|---|---|
| ØA | ØB | C | ØD | E | ||
| U1 | 1 | 2.46 | 1.40 | 40 | - | - |
| U2 | 2 | 2.50 | 1.80 | 40 | - | - |
| U3 | 3 | 2.50 | 1.40 | 34 | - | - |
| U4 | 4 | 2.50 | 1.40 | 38 | - | - |
| U5 | 5 | 2.50 | 1.40 | 40 | - | - |
| U6 | 6 | 2.50 | 1.40 | 42 | - | - |
| U7 | 7 | 2.50 | 1.80 | 38 | - | - |
| U8 | 8 | 2.50 | 1.80 | 42 | - | - |
| U9 | 9 | 2.48 | 1.00 | 28 | 2.16 | 18 |
| U10 | 10 | 2.50 | 1.00 | 30 | 2.06 | 18 |
| U11 | 11 | 2.50 | 1.00 | 28 | 2.11 | 16 |
| U12 | 12 | 2.50 | 1.40 | 32 | - | - |
| U13 | 13 | 2.45 | 1.20 | 28 | - | - |
| U14 | 14 | 2.48 | 0.60 | 28 | 2.23 | 18 |
| U15 | 15 | 2.50 | 1.20 | 32 | - | - |
| U16 | 16 | 2.50 | 1.80 | 32 | - | - |
| U17 | 17 | 2.50 | 0.60 | 35 | - | - |
| U18 | 18 | 2.48 | 1.00 | 34 | - | - |
| U19 | 19 | 2.44 | 1.00 | 32.5 | - | - |
| U20 | 20 | 2.44 | 1.00 | 34.5 | - | - |
| U21 | 21 | 2.44 | 1.00 | 36 | - | - |
| U22 | 22 | 2.50 | 1.00 | 36.5 | - | - |
| U23 | 23 | 2.46 | 1.00 | 36.5 | - | - |
| U24 | 24 | 2.46 | 1.00 | 34 | - | - |
| U25 | 25 | 2.48 | 1.00 | 36.5 | - | - |
Slide needle specifications for PHBE-PHF-PHM-PHSB-VHSB carburetors (K slides)
This information was gleaned from eurocarb. I meticulously recreated the table of values from a difficult to read original. Therefore, mistakes may be present. Here is a link to the original image in case you would like to scrutinize any particulars.
PHBE-PHF-PHM-PHSB-VHSB slide carburetor needle. Note the term 'cilindrico' which translates to 'cylindrical'.
Table: Slide needle series 8530 X 08 K
| Type | Value X | Characteristic expressed in millimeters | |||||
|---|---|---|---|---|---|---|---|
| ØA | ØB | C | ØD | E | F | ||
| K1 | 1 | 2.45 | 1.75 | 37 | - | - | - |
| K2 | 2 | 2 45 | 1.75 | 42 | - | - | - |
| K3 | 3 | 2.50 | 1.50 | 39 | - | - | - |
| K4 | 4 | 2.45 | 1.50 | 39 | - | - | - |
| K5 | 5 | 2.45 | 1.50 | 37 | - | - | - |
| K6 | 6 | 2.45 | 1.75 | 39 | - | - | - |
| K7 | 7 | 2.45 | 1.25 | 39 | - | - | - |
| K8 | 8 | 2.50 | 1.50 | 37 | - | - | - |
| K9 | 9 | 2.45 | 1.50 | 42 | - | - | - |
| K11 | 11 | 2.50 | 1.25 | 39 | - | - | - |
| K12 | 12 | 2.45 | 1.75 | 32 | - | - | - |
| K13 | 13 | 2.45 | 1.25 | 36 | - | - | - |
| K14 | 14 | 2.40 | 1.75 | 33 | - | - | - |
| K15 | 15 | 2.60 | 0.60 | 36 | - | - | - |
| K16 | 16 | 2.60 | 1.75 | 39 | - | - | - |
| K17 | 17 | 2.42 | 1.75 | 40 | - | - | - |
| K18 | 18 | 2.60 | 1.40 | 35 | - | - | - |
| K19 | 19 | 2.50 | 1.40 | 40 | - | - | - |
| K20 | 20 | 2.50 | 1.40 | 42 | - | - | - |
| K21 | 21 | 2.50 | 1.80 | 38 | - | - | - |
| K22 | 22 | 2.50 | 1.80 | 40 | - | - | - |
| K23 | 23 | 2.50 | 1.80 | 42 | - | - | - |
| K24 | 24 | 2.50 | 1.20 | 38 | 2.13 | 18 | - |
| K25 | 25 | 2.50 | 1.00 | 36 | 2.15 | 18 | - |
| K27 | 27 | 2.50 | 1.00 | 44 | - | - | - |
| K28 | 28 | 2.50 | 1.00 | 41 | - | - | - |
| K29 | 29 | 2.45 | 1.25 | 42 | - | - | - |
| K30 | 30 | 2.50 | 1.40 | 36 | 2 15 | 18 | - |
| K32 | 32 | 2.48 | 1.70 | 44 | - | - | - |
| K31 | 31 | 2.45 | 1.50 | 36 | - | - | - |
| K33* | 33 | 2.60 | 1.80 | 44 | - | - | - |
| K34 | 34 | 2.50 | 1.40 | 40 | 2.11 | 18 | - |
| K35 | 35 | 2.50 | 1.40 | 43 | - | - | - |
| K36 | 36 | 2.50 | 1.40 | 38 | 2.17 | 20 | - |
| K37 | 37 | 2.50 | 1.40 | 39 | 2.12 | 18 | - |
| K38 | 38 | 2.50 | 1.40 | 38 | 2.13 | 18 | - |
| K39 | 39 | 2.48 | 1.45 | 36 | 2.28 | 26 | - |
| K40 | 40 | 2.50 | 1.40 | 40 | 2.18 | 22 | - |
| K41 | 41 | 2.50 | 1.40 | 40 | 2.14 | 22 | - |
| K42 | 42 | 2.50 | 1.40 | 38 | 2.16 | 22 | - |
| K43 | 43 | 2.50 | 1.40 | 42 | 2.16 | 26 | - |
| K44 | 44 | 2.50 | 1.40 | 39 | 2.06 | 20 | - |
| K45 | 45 | 2.48 | 1.30 | 36 | 2.28 | 26 | - |
| K46 | 46 | 2.50 | 1.00 | 40 | 2.16 | 20 | - |
| K48 | 48 | 2.48 | 1.00 | 36 | 2 26 | 25 | 11 |
| K49 | 49 | 2.50 | 1.40 | 39 | 2.20 | 26 | - |
| K50 | 50 | 2.50 | 1.40 | 39 | 2.27 | 26 | - |
| K51 | 51 | 2.52 | 1.40 | 43 | - | - | - |
| K52 | 52 | 2.50 | 1.60 | 36 | 2.25 | 25 | 11 |
| K53 | 53 | 2.52 | 1.60 | 36 | 2.25 | 25 | 11 |
| K54 | 54 | 2.45 | 1.50 | 40 | 2.108 | 18 | - |
| K56 | 56 | 2.50 | 1.20 | 38 | 2.17 | 20 | - |
| K57 | 57 | 2.50 | 1.40 | 37 | 2.232 | 25 | - |
| K58 | 58 | 2.40 | 1.60 | 30 | 2.25 | 25 | 11 |
| K59 | 59 | 2.50 | 1.40 | 39 | 2.23 | 24 | - |
| K60 | 60 | 2.46 | 1.60 | 39 | 2.13 | 25 | 11 |
| K61 | 61 | 2.44 | 1.60 | 39 | 2.13 | 26 | 11 |
| K62 | 62 | 2.48 | 1.60 | 39 | 2.13 | 26 | 11 |
| K63 | 63 | 2.46 | 1.60 | 39 | 2.10 | 25 | 11 |
| K65 | 65 | 2.45 | 1.60 | 39 | 2.16 | 25 | 11 |
| K66 | 66 | 2.44 | 1.60 | 39 | 2.16 | 25 | 11 |
| K67 | 67 | 2.44 | 1.60 | 39 | 2.10 | 25 | 11 |
| K68 | 68 | 2.42 | 1.60 | 39 | 2.07 | 26 | 11 |
| K69 | 69 | 2.48 | 1.50 | 39 | 2.10 | 25 | 11 |
| K70 | 70 | 2.42 | 1.60 | 39 | 2.04 | 25 | 11 |
| K71 | 71 | 2.44 | 1.60 | 39 | 2.07 | 25 | 11 |
| K72 | 72 | 2.50 | 1.20 | 38 | 2.20 | 22 | - |
| K76 | 76 | 2.46 | 1.55 | 39 | 2.50 | 25 | 11 |
| K77 | 77 | 2.46 | 1.60 | 39 | 2.07 | 25 | 11 |
| K78 | 78 | 2.48 | 1.60 | 30 | 2.07 | 25 | 11 |
| K79 | 79 | 2.40 | 1.60 | 39 | 2.07 | 25 | 11 |
| K80 | 80 | 2.40 | 1.60 | 39 | - | - | - |
| K81 | 81 | 2.44 | 1.55 | 39 | 2.07 | 25 | 11 |
| K82 | 82 | 2.48 | 1.55 | 39 | 2.10 | 25 | 11 |
| K83 | 83 | 2.44 | 1.55 | 39 | 2.04 | 26 | 11 |
| K84 | 84 | 2.48 | 1.60 | 39 | 2.10 | 26 | 11 |
| K86 | 86 | 2.46 | 1.60 | 39 | 2.07 | 26 | 11 |
| K87 | 87 | 2.48 | 1.45 | 39 | 2.10 | 25 | 11 |
| K88 | 88 | 2.56 | 1.43 | 32.4 | 2.12 | 16.2 | - |
| K89 | 89 | 2.48 | 1.50 | 39 | 2.07 | 25 | 11 |
| K90 | 90 | 2.50 | 1.75 | 42 | - | - | - |
| K91 | 91 | 2.47 | 1.40 | 39 | 2.27 | 26 | - |
| K92 | 92 | 2.50 | 1.60 | 38 | - | - | - |
| K93 | 93 | 2.50 | 1.60 | 40 | - | - | - |
| K94 | 94 | 2.50 | 1.65 | 38 | - | - | - |
| K95 | 95 | 2.50 | 1.65 | 40 | - | - | - |
| * Constructed of anodized aluminum | |||||||
Slide needle specifications for PHBG carburetors (W slides)
This information was gleaned from eurocarb. I meticulously recreated the table of values from a difficult to read original. Therefore, mistakes may be present. Here is a link to the original image in case you would like to scrutinize any particulars.
PHBG carburetor slide needle
Table: Slide needle series 9595 X 08 W
| Type | Value X | Characteristic expressed in millimeters | ||
|---|---|---|---|---|
| ØA | ØB | C | ||
| W1 | 1 | 2.45 | 0.60 | 24 |
| W2 | 2 | 2.45 | 0.50 | 22 |
| W3 | 3 | 2.45 | 1.40 | 20 |
| W4 | 4 | 2.45 | 1.40 | 18 |
| W5 | 5 | 2.45 | 1.40 | 15 |
| W6 | 6 | 2.50 | 1.00 | 24 |
| W7 | 7 | 2.50 | 1.40 | 18 |
| W8 | 8 | 2.50 | 1.40 | 15 |
| W9 | 9 | 2.50 | 1.40 | 20 |
| W10 | 10 | 2.50 | 1.80 | 15 |
| W11 | 11 | 2.50 | 1.80 | 18 |
| W12 | 12 | 2.50 | 1.80 | 20 |
| W13 | 13 | 2.50 | 0.50 | 22 |
| W14 | 14 | 2.50 | 0.50 | 24 |
| W15* | 15 | 2.50 | 0.60 | 25 |
| W16 | 16 | 2.50 | 1.00 | 22 |
| W17 | 17 | 2.50 | 1.00 | 26 |
| W18 | 18 | 2.45 | 0.50 | 24 |
| W19* | 19 | 2.50 | 1.80 | 20 |
| W20 | 20 | 2.50 | 1.60 | 24 |
| W21* | 21 | 2.50 | 1.60 | 24 |
| W22*~ | 22 | 2.50 | 0.60 | 25 |
| W23 | 23 | 2.50 | 0.60 | 26 |
| W24 | 24 | 2.50 | 1.80 | 24 |
| W25 | 25 | 2.50 | 1.80 | 22 |
| * Constructed of anodized aluminum ~ Differs from W15 in length; W22 has a length of 42.6 | ||||
Slide needle specifications for PHBH carburetors (X slides)
This information was gleaned from eurocarb. I meticulously recreated the table of values from a difficult to read original. Therefore, mistakes may be present. Here is a link to the original image in case you would like to scrutinize any particulars.
PHBH carburetor slide needle
Table: Slide needle series 9477 X 08 X
| Type | Value X | Characteristic expressed in millimeters | ||||
|---|---|---|---|---|---|---|
| ØA | ØB | C | ØD | E | ||
| X1 | 1 | 2.48 | 1.20 | 26 | - | - |
| X2 | 2 | 2.50 | 1.80 | 24 | - | - |
| X3 | 3 | 2.46 | 1.60 | 22 | - | - |
| X4 | 4 | 2.48 | 1.80 | 20 | - | - |
| X5 | 5 | 2.46 | 1.80 | 24 | - | - |
| X6 | 6 | 2.50 | 1.20 | 26 | - | - |
| X7 | 7 | 2.50 | 1.50 | 20 | - | - |
| X8 | 8 | 2.50 | 1.40 | 26 | - | - |
| X9 | 9 | 2.50 | 1.40 | 18 | - | - |
| X10 | 10 | 2.50 | 1.40 | 20 | - | - |
| X11 | 11 | 2.50 | 1.40 | 22 | - | - |
| X12 | 12 | 2.50 | 1.80 | 18 | - | - |
| X13 | 13 | 2.50 | 1.80 | 22 | - | - |
| X14 | 14 | 2.50 | 0.80 | 24 | - | - |
| X15 | 15 | 2.50 | 0.80 | 26 | - | - |
| X16 | 16 | 2.50 | 0.80 | 28 | - | - |
| X17 | 17 | 2.50 | 1.20 | 24 | - | - |
| X18 | 18 | 2.50 | 1.20 | 28 | - | - |
| X19 | 19 | 2.45 | 1.00 | 28 | - | - |
| X20 | 20 | 2.42 | 1.00 | 22 | - | - |
| X21 | 21 | 2.50 | 1.00 | 20 | - | - |
| X22 | 22 | 2.48 | 1.20 | 25.5 | - | - |
| X23 | 23 | 2.48 | 1.20 | 26 | - | - |
| X24 | 24 | 2.50 | 1.00 | 30 | - | - |
| X25 | 25 | 2.50 | 1.80 | 25 | - | - |
| X27 | 27 | 2.48 | 1.40 | 20 | - | - |
| X28 | 28 | 2.50 | 1.20 | 26 | 2.38 | 20 |
| X29 | 29 | 2.50 | 0.60 | 30 | - | - |
| X30 | 30 | 2.50 | 1.00 | 28 | 2.30 | 20 |
| X31 | 31 | 2.48 | 1.20 | 28 | - | - |
| X32 | 32 | 2.48 | 1.50 | 24 | - | - |
| X33 | 33 | 2.50 | 1.00 | 32 | - | - |
| X34 | 34 | 2.48 | 1.20 | 29 | 2.34 | 15 |
| X35 | 35 | 2.48 | 0.80 | 25 | 2.32 | 20 |
| X36 | 36 | 2.53 | 0.60 | 30 | - | - |
| X37~ | 37 | 2.53 | 0.60 | 30 | - | - |
| X38 | 38 | 2.48 | 1.20 | 28 | 2.28 | 20 |
| X39 | 39 | 2.50 | 0.80 | 26 | 2.33 | 20 |
| X40 | 40 | 2.50 | 0.80 | 27 | 2.33 | 24 |
| X41 | 41 | 2.48 | 1.00 | 29 | 2.43 | 27 |
| X42 | 42 | 2.53 | 0.65 | 29.25 | - | - |
| X43 | 43 | 2.50 | 0.80 | 24 | 2.38 | 18 |
| X44 | 44 | 2.46 | 1.80 | 22 | - | - |
| X45 | 45 | 2.48 | 0.80 | 24.5 | 2.30 | 18 |
| X46 | 46 | 2.50 | 1.20 | 23 | - | - |
| X47 | 47 | 2.50 | 1.80 | 30 | 2.35 | 15 |
| X48 | 48 | 2.47 | 1.80 | 29 | - | - |
| X49 | 49 | 2.50 | 1.20 | 22 | - | - |
| X50 | 50 | 2.50 | 1.20 | 25 | - | - |
| X51 | 51 | 2.50 | 1.20 | 24 | 2.37 | 18 |
| X52 | 52 | 2.52 | 0.98 | 29.46 | - | - |
| X53 | 53 | 2.53 | 0.60 | 28 | 2.40 | 24 |
| X54 | 54 | 2.50 | 1.30 | 20 | 2.35 | 20 |
| X55 | 55 | 2.51 | 0.98 | 29.25 | - | - |
| X56 | 56 | 2.50 | 0.80 | 26 | 2.36 | 22 |
| X57 | 57 | 2.50 | 0.98 | 20.05 | - | - |
| X58* | 58 | 2.50 | 0.60 | 30 | - | - |
| X59 | 59 | 2.50 | 1.00 | 21 | - | - |
| X60 | 60 | 2.54 | 1.00 | 28 | - | - |
| X61 | 61 | 2.46 | 1.50 | 20 | - | - |
| X62 | 62 | 2.50 | 1.00 | 30 | 2.31 | 22 |
| X63 | 63 | 2.50 | 1.20 | 27 | - | - |
| X64 | 64 | 2.50 | 1.50 | 30 | 2.31 | 22 |
| X65 | 65 | 2.52 | 1.00 | 34 | - | - |
| X66 | 66 | 2.53 | 0.98 | 29.65 | - | - |
| X67 | 67 | 2.52 | 1.00 | 32 | - | - |
| X68 | 68 | 2.45 | 1.80 | 28.14 | - | - |
| X69* | 69 | 2.52 | 0.98 | 29.45 | - | - |
| X70 | 70 | 2.52 | 0.65 | 29.09 | - | - |
| X71 | 71 | 2.48 | 1.00 | 29 | - | - |
| X72* | 72 | 2.52 | 1.02 | 29.55 | - | - |
| X73 | 73 | 2.52 | 1.02 | 29.55 | - | - |
| X74 | 74 | 2.52 | 1.00 | 30 | - | - |
| X75 | 75 | 2.52 | 1.60 | 29 | - | - |
| X76 | 76 | 2.52 | 1.60 | 29.36 | - | - |
| X77 | 77 | 2.48 | 0.80 | 26 | - | - |
| X78 | 78 | 2.52 | 1.55 | 29.22 | - | - |
| X79 | 79 | 2.51 | 1.01 | 28.17 | - | - |
| X80 | 80 | 2.50 | 1.20 | 26 | - | - |
| X81 | 81 | 2.48 | 1.00 | 24 | - | - |
| X82 | 82 | 2.53 | 0.98 | 29.45 | - | - |
| X83 | 83 | 2.53 | 0.98 | 28.85 | - | - |
| X84 | 84 | 2.52 | 0.98 | 29.45 | - | - |
| X85 | 85 | 2.48 | 1.00 | 32 | - | - |
| X86 | 86 | 2.50 | 1.60 | 29 | - | - |
| X87 | 87 | 2.54 | 1.40 | 30 | - | - |
| X88 | 88 | 2.50 | 1.20 | 28 | - | - |
| * Constructed of anodized aluminum ~ Differs from X36 in length; X37 has a length of 56.2 | ||||||
Slide needle specifications for PHBL carburetors - (D slides)
This information was gleaned from eurocarb. I meticulously recreated the table of values from a difficult to read original. Therefore, mistakes may be present. Here is a link to the original image in case you would like to scrutinize any particulars.
PHBL carburetor slide needle
Table: Slide needle series 2265 X 08 D
| Type | Value X | Characteristic expressed in millimeters | ||||
|---|---|---|---|---|---|---|
| ØA | ØB | C | ØD | E | ||
| D1 | 1 | 2.45 | 1.60 | 15.4 | - | - |
| D3 | 3 | 2.42 | 1.60 | 14 | - | - |
| D21 | 21 | 2.50 | 1.80 | 20.2 | - | - |
| D22 | 22 | 2.50 | 1.40 | 18 | - | - |
| D23 | 23 | 2.46 | 1.00 | 22 | - | - |
| D24 | 24 | 2.50 | 0.60 | 20 | - | - |
| D25 | 25 | 2.50 | 1.40 | 16 | - | - |
| D26 | 26 | 2.50 | 1.40 | 20 | - | - |
| D27 | 27 | 2.50 | 1.80 | 16 | - | - |
| D28 | 28 | 2.50 | 1.80 | 18 | - | - |
| D29 | 29 | 2.50 | 1.80 | 20 | - | - |
| D30 | 30 | 2.50 | 0.60 | 18 | - | - |
| D31 | 31 | 2.50 | 0.60 | 22 | - | - |
| D32 | 32 | 2.50 | 1.00 | 18 | - | - |
| D33 | 33 | 2.50 | 1.00 | 20 | - | - |
| D34 | 34 | 2.50 | 1.00 | 22 | - | - |
| D35 | 35 | 2.46 | 1.40 | 18 | - | - |
| D36 | 36 | 2.50 | 1.40 | 22 | - | - |
| D37 | 37 | 2.50 | 1.40 | 24 | - | - |
| D40 | 40 | 2.48 | 1.00 | 24 | - | - |
| D41 | 41 | 2.52 | 1.00 | 24.5 | - | - |
| D42 | 42 | 2.46 | 0.60 | 24 | 2.295 | 18 |
| D43 | 43 | 2.50 | 0.60 | 26 | 2.227 | 18 |
| D44 | 44 | 2.48 | 1.60 | 24 | - | - |
| D45* | 45 | 2.50 | 0.60 | 26 | 2.227 | 18 |
| D46 | 46 | 2.50 | 1.00 | 24 | - | - |
| * Constructed of anodized aluminum | ||||||
Slide needle specifications for PHVA-PHBN carburetors - (A slides)
This information was gleaned from eurocarb. I meticulously recreated the table of values from a difficult to read original. Therefore, mistakes may be present. Here is a link to the original image in case you would like to scrutinize any particulars.
PHVA-PHBN carburetor slide needle
Table: Slide needle series 13680 X 08 A
| Type | Value X | Characteristic expressed in millimeters | |||
|---|---|---|---|---|---|
| ØA | ØB | C | D | ||
| A02 | 02 | 2 | 0.6 | 20 | 12 |
| A07 | 07 | 2 | 1 | 18 | 14 |
| A08 | 08 | 2 | 1 | 20 | 12 |
| A10 | 10 | 2.02 | 0.6 | 18 | 14 |
| A11 | 11 | 2.02 | 0.6 | 20 | 12 |
| A12 | 12 | 2 | 1.79 | 20 | 12 |
| A13 | 13 | 2 | 1.79 | 22 | 10 |
| A14 | 14 | 2.07 | 1 | 18 | 14 |
| A15 | 15 | 1.98 | 1.77 | 20 | 12 |
| A18 | 18 | 2.04 | 0.61 | 21.9 | 10.07 |
| A19 | 19 | 1.93 | 1.77 | 20.3 | 11.7 |
| A20 | 20 | 2 | 1.6 | 20 | 12 |
| A21 | 21 | 1.99 | 1.79 | 18.1 | 13.8 |
| A23 | 23 | 1.98 | 1 | 18 | 14 |
| A24 | 24 | 1.99 | 1 | 20 | 12 |
| A25 | 25 | 2.02 | 1.4 | 20 | 12 |
| A26 | 26 | 2 | 1.9 | 20 | 12 |
| A27 | 27 | 1.98 | 1.8 | 20 | 12 |
| A28 | 28 | 1.99 | 1.8 | 20 | 12 |
| A29 | 29 | 2.02 | 1.2 | 20 | 12 |
| A30 | 30 | 1.99 | 1.40 | 20 | 12 |
| A31 | 31 | 1.98 | 1.40 | 20 | 12 |
| A32 | 32 | 1.98 | 1.70 | 20 | 12 |
| A33 | 33 | 2 | 1 | 21 | 11 |
Slide needle specifications for PHVB carburetors (M slides)
This information was gleaned from eurocarb. I meticulously recreated the table of values from a difficult to read original. Therefore, mistakes may be present. Here is a link to the original image in case you would like to scrutinize any particulars.
PHVB carburetor slide needle
Table: Slide needle series 15377 X 08 M
| Type | Value X | Characteristic expressed in millimeters | |||||
|---|---|---|---|---|---|---|---|
| ØA | ØB | C | D | ØF | G | ||
| M1 | 1 | 2 | 1.1 | 19.5 | 19.9 | ||
| M2 | 2 | 2.02 | 1.1 | 26 | 13.4 | 1.97 | 20 |
| M3 | 3 | 2.02 | 1.1 | 20.5 | 18.9 | ||
| M4 | 4 | 2.02 | 1.1 | 21.5 | 17.9 | ||
| M5 | 5 | 2 | 0.6 | 19.5 | 10.9 | ||
| M6 | 6 | 2.02 | 1.1 | 22.5 | 16.9 | ||
| M7 | 7 | 2.02 | 0.6 | 23 | 16.4 | 1.97 | 21 |
Slide needle specifications for VHB carburetors - (V slides)
This information was gratefully provided by Chris Oates, who was sent this information by eurocarb. I meticulously recreated the table of values from a somewhat difficult to read original. Therefore, mistakes may be present. Here is a link to the original image in case you would like to scrutinize any particulars.
VHB carburetor slide needle
Table: Slide needle series V
| Type | Value X | Characteristic expressed in millimeters | ||||
|---|---|---|---|---|---|---|
| ØA | ØB | C | D | E | ||
| V1 | 1 | 2.47 | 0.75 | 23.5 | 67.5 | 73.5 |
| V2 | 2 | 2.5 | 1.9 | 22 | 67.5 | 73.5 |
| V3 | 3 | 2.48 | 1.5 | 22 | 67.5 | 73.5 |
| V4 | 4 | 2.5 | 1.5 | 22 | 67.5 | 73.5 |
| V5 | 5 | 2.48 | 1.8 | 27 | 72.5 | 78.5 |
| V6 | 6 | 2.45 | 1.9 | 20 | 67.5 | 73.5 |
| V7 | 7 | 2.45 | 1.5 | 20 | 67.5 | 73.5 |
| V8 | 8 | 2.45 | 1.7 | 18.5 | 67.5 | 73.5 |
| V9 | 9 | 2.48 | 1.8 | 26 | 72.5 | 78.5 |
| V10 | 10 | 2.47 | 1.5 | 23.5 | 67.5 | 73.5 |
| V11 | 11 | 2.47 | 2.5 | 23.5 | 67.5 | 73.5 |
| V12 | 12 | 2.5 | 1.5 | 20 | 67.5 | 73.5 |
| V13 | 13 | 2.5 | 1.7 | 24 | 67.5 | 73.5 |
| V14 | 14 | 2.4 | 2.1 | 20 | 72.5 | 78.5 |
| V15 | 15 | 2.48 | 1.5 | 26 | 67.5 | 73.5 |
| V16 | 16 | 2.47 | 1 | 25 | 67.5 | 72.5 |
Slide needle specifications for VHBZ-PHSA carburetors - (E slides)
This information was gleaned from eurocarb. I meticulously recreated the table of values from a difficult to read original. Therefore, mistakes may be present. Here is a link to the original image in case you would like to scrutinize any particulars.
VHBZ-PHSA carburetor slide needle
Table: Slide needle series 2343 X 08 E
| Type | Value X | Characteristic expressed in millimeters | |||||
|---|---|---|---|---|---|---|---|
| ØA | ØB | C | ØD | E | F | ||
| E1 | 1 | 2.45 | 2.00 | 19 | - | - | 65 |
| E2 | 2 | 2.42 | 1.30 | 20 | - | - | 65 |
| E3 | 3 | 2.50 | 1.30 | 23 | - | - | 65 |
| E4 | 4 | 2.45 | 1.30 | 22 | - | - | 65 |
| E5 | 5 | 2.43 | 1.30 | 21.5 | - | - | 65 |
| E6 | 6 | 2.42 | 2.00 | 18 | - | - | 65 |
| E7 | 7 | 2.40 | 2.00 | 17 | - | - | 65 |
| E8 | 8 | 2 50 | 0.50 | 23 | - | - | 65 |
| E9 | 9 | 2 50 | 0.50 | 20 | - | - | 62 |
| E10 | 10 | 2.45 | 0.50 | 19.5 | - | - | 62 |
| E11 | 11 | 2.42 | 0.50 | 19.2 | - | - | 62 |
| E12 | 12 | 2.45 | 1.25 | 19.2 | - | - | 62 |
| E13 | 13 | 2.50 | 1.30 | 25 | - | - | 65 |
| E14 | 14 | 2 45 | 0.50 | 21.5 | - | - | 62 |
| E15 | 15 | 2.43 | 1.30 | 22.5 | - | - | 65 |
| E16 | 16 | 2.45 | 0.50 | 22.5 | - | - | 65 |
| E17 | 17 | 2.45 | 1.70 | 20 | - | - | 65 |
| E18 | 18 | 2.50 | 1.30 | 26 | - | - | 65 |
| E19 | 19 | 2.42 | 1.00 | 21 | - | - | 65 |
| E20 | 20 | 2.45 | 1.70 | 17 | - | - | 62 |
| E22 | 22 | 2.42 | 1.70 | 17 | - | - | 65 |
| E23 | 23 | 2.45 | 1.70 | 17 | - | - | 65 |
| E24 | 24 | 2.45 | 1.70 | 21.5 | - | - | 65 |
| E25 | 25 | 2.45 | 0.75 | 19 | - | - | 55 |
| E26 | 26 | 2.45 | 1.25 | 18 | - | - | 65 |
| E27 | 27 | 2.42 | 1.25 | 18 | - | - | 65 |
| E28 | 28 | 2.45 | 0.75 | 22 | - | - | 65 |
| E29 | 29 | 2.48 | 1.25 | 23 | - | - | 65 |
| E30 | 30 | 2.40 | 1.90 | 17 | - | - | 65 |
| E31 | 31 | 2 42 | 1.50 | 18 | - | - | 65 |
| E32 | 32 | 2.45 | 1.00 | 21 | - | - | 65 |
| E33 | 33 | 2.50 | 1.70 | 21 | - | - | 65 |
| E35 | 35 | 2.42 | 0.75 | 18 | - | - | 65 |
| E36 | 36 | 2.45 | 1.60 | 24.5 | - | - | 70 |
| E37 | 37 | 2.45 | 1.50 | 17 | - | - | 65 |
| E38 | 38 | 2.50 | 1.00 | 26 | - | - | 65 |
| E39 | 39 | 2.50 | 0.95 | 25 | - | - | 65 |
| E40 | 40 | 2.42 | 1.25 | 24 | - | - | 65 |
| E41 | 41 | 2.45 | 1.50 | 32 | - | - | 65 |
| E42 | 42 | 2.50 | 1.50 | 18 | - | - | 65 |
| E43 | 43 | 2.45 | 1.25 | 20 | - | - | 65 |
| E51 | 51 | 2.45 | 1.60 | 20 | - | - | 65 |
| E52 | 52 | 2.50 | 1.70 | 29 | 2.19 | 13 | 65 |