Gregory Bender

Dual instrument dash

Created:

Updated:

// //

Short pigtail for the neutral indicator light

Applicable to these part numbers:

  1. Connect the green wire with the 6.3 mm spade terminal to either terminal of the corresponding bulb holder.

Short pigtail for the oil pressure indicator light

Applicable to these part numbers:

  1. Connect the gray wire with the 6.3 mm spade terminal to either terminal of the corresponding bulb holder.

Short pigtail for the generator indicator light

Applicable to these part numbers:

  1. Connect the red wire with the 6.3 mm spade terminal to either terminal of the corresponding bulb holder.

Indicator light interconnect

  1. Connect the white/black wire with the 4 mm female bullet terminal to the corresponding white/black wire with the 4 mm male bullet terminal.
  2. Connect each 6.3 mm spade terminal to either terminal of each bulb holder for the indicator lights.
  3. IF PRESENT, connect the blue wire with the 6.3 mm spade terminal to the positive terminal on the tachometer.
Tachometer wire connections applicable to Moto Guzzi V700, V7 Special, Ambassador, 850 GT, 850 GT California, Eldorado, and 850 California Police models
Tachometer wire connections applicable to Moto Guzzi V700, V7 Special, Ambassador, 850 GT, 850 GT California, Eldorado, and 850 California Police models

Photo courtesy of Gregory Bender.

Tachometer wire connections applicable to Moto Guzzi V700, V7 Special, Ambassador, 850 GT, 850 GT California, Eldorado, and 850 California Police models

Photo courtesy of Gregory Bender.

Direct link to image

Illumination light interconnect

Applicable to these part numbers:

  1. Connect the white wire with the joined 4 mm female bullet terminal to the corresponding white wire with the 4 mm female bullet terminal.
  2. Connect each 4 mm female bullet terminal to the corresponding bulb holder for the illumination lights for each gauge.

Tachometer ground

Applicable to these part numbers:

  1. Connect the black wire with the 3 mm ring terminal to the ground post on the tachometer.
  2. Connect the other end of the black wire with the 6 mm ring terminal to a ground point on the top triple tree plate.
Tachometer wire connections applicable to Moto Guzzi V700, V7 Special, Ambassador, 850 GT, 850 GT California, Eldorado, and 850 California Police models
Tachometer wire connections applicable to Moto Guzzi V700, V7 Special, Ambassador, 850 GT, 850 GT California, Eldorado, and 850 California Police models

Photo courtesy of Gregory Bender.

Tachometer wire connections applicable to Moto Guzzi V700, V7 Special, Ambassador, 850 GT, 850 GT California, Eldorado, and 850 California Police models

Photo courtesy of Gregory Bender.

Direct link to image

Tachometer

Applicable to these part numbers:

  1. At the distributor, connect the black wire with the 5 mm ring terminal to the 5 mm post on the side of the body of the distributor.
  2. Route the wire under the frame, along the left side of the frame, and up through the left most hole in the top triple tree plate.
  3. Connect the 6.3 mm spade terminal to the negative terminal on the tachometer.
  4. IF PRESENT, connect the terminals on the other wire to the positive terminal on the tachometer and the positive terminal on the coil.
Tachometer wire connections applicable to Moto Guzzi V700, V7 Special, Ambassador, 850 GT, 850 GT California, Eldorado, and 850 California Police models
Tachometer wire connections applicable to Moto Guzzi V700, V7 Special, Ambassador, 850 GT, 850 GT California, Eldorado, and 850 California Police models

Photo courtesy of Gregory Bender.

Tachometer wire connections applicable to Moto Guzzi V700, V7 Special, Ambassador, 850 GT, 850 GT California, Eldorado, and 850 California Police models

Photo courtesy of Gregory Bender.

Direct link to image