Subject: Re: Roadside repairs
Author: mike behn
Date: Jan 22, 2004, 1:56 PM
Post ID: 1715828740
This is a multi-part message in MIME format.
--Boundary_(ID_T4Z6Bf9CAOHLEoNYAUYLdA)
Content-type: text/plain; charset=us-ascii; format=flowed
Content-transfer-encoding: 7BIT
charlie, when are you ordering it from? I use to use it and was told
that it is no longer made. it always seemed to take out the shimmy at
high speeds. mike denver 71 ambo
Charlie Mullendore wrote:
| In Motorcycle Consumer News they had a piece on gutting a Campbell-Hausefield 12 volt, 250 psi mini-compressor and using just the mechanical bits to carry along on trips just in case. What's left after you remove all the plastic housing is about the right size to fit in a Loops toolbox. Good also for inflating air mattresses when you set up camp too. For years I've been using PJ1 Balance Plus in my tube-type tires. It not only balances well, but seals small punctures. It's kind of a grey goo with a cream-of-wheat consistency. Hard to find in motorcycle shops now, I usually have to mail order it. Cheers, Charlie Kevin Graf wrote:
|
--
Michael Behn
A & M Window Service. Inc.
Phone (303) 450-2200 Fax (303) 450-2730
--Boundary_(ID_T4Z6Bf9CAOHLEoNYAUYLdA)
Content-type: text/html; charset=us-ascii
Content-transfer-encoding: 7BIT
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN">
<html>
<head>
<meta http-equiv="Content-Type" content="text/html;charset=ISO-8859-1">
<title></title>
</head>
<body text="#000000" bgcolor="#ffffff">
charlie, when are you ordering it from? I use to use it and was told
that it is no longer made. it always seemed to take out the shimmy at
high speeds. mike denver 71 ambo<br>
<br>
Charlie Mullendore wrote:<br>
<blockquote type="cite"
cite="mid966388109-1463-@boing.topica.com">
<pre wrap="">In Motorcycle Consumer News they had a piece on gutting a
Campbell-Hausefield 12 volt, 250 psi mini-compressor and using just the
mechanical bits to carry along on trips just in case. What's left after
you remove all the plastic housing is about the right size to fit in a
Loops toolbox. Good also for inflating air mattresses when you set up
camp too.
For years I've been using PJ1 Balance Plus in my tube-type tires. It not
only balances well, but seals small punctures. It's kind of a grey goo
with a cream-of-wheat consistency. Hard to find in motorcycle shops now,
I usually have to mail order it. Cheers,
Charlie
Kevin Graf wrote:
</pre>
<blockquote type="cite">
<pre wrap="">My pal Kevin had a nail puncture his rear tire on his eldo. He was about
5
mile from his home. The guy never carries tools..? Must have faith in my
mechanic ability???? Anyways, He bought the tire inflator goo. A small
can
he said, smaller that the typical size I guess. It worked. Damn tire
inflated and stayed that way. For weeks, until we convinced him to at
least
change the tube! Tube and everything stayed inflated.... Alien
technology is
the best.
I have never had to change on the side of the road. It's not all that
easy
with the best tire changing machines, let alone with irons. I have had
to
pry off & on tires with irons and it is not fun,pretty crappy job let
alone
on the side of the road. I will carry tire goo and get my self home or
to a
shop, then deal with it. Mechanics hate the goo, with a vengeance, So I
will
tear the tire off myself and clean it if possible, If not, apologize
profusely and tip well. One good thing is that most of the goo stays in
the
tube.
If want to play on the "safe" side, there are kits out there. The
majority
of them are for tubeless type. Plugs, ect. But the are some with the
tube
patches. Then you have to air the tire up. Again there are gadgets that
have
a fitting for the spark plug holes, screw that puppy in, attach the
hose,
and start cranking the engine. I suppose it would put a few psi into the
tire before other things happened. Now you can be left with a dead
battery
and a very hot starter. I have on of the things made by Yamaha. Never
used
it. knock, knock.
I think there are CO2 fillers out there, not too sure if these work any
better.
</pre>
</blockquote>
<pre wrap=""><!---->
</pre>
</blockquote>
<br>
<pre class="moz-signature" cols="72">--
Michael Behn
A & M Window Service. Inc.
Phone (303) 450-2200 Fax (303) 450-2730
</pre>
</body>
</html>
--Boundary_(ID_T4Z6Bf9CAOHLEoNYAUYLdA)--