Topica Loopframe_Guzzi Archive


Subject: RE: Starter problem still....

Author: Robert Hawkes

Date: Apr 7, 2005, 6:11 PM

Post ID: 1718667246



Lannis, Centauros, East Coast, where? Bob

-----Original Message-----
From: Lannis [mailto:lan-@direcway.com]
Sent: Thursday, April 07, 2005 4:43 PM
To: Loopfram-@topica.com
Subject: RE: Starter problem still....

Your free subscription is supported by today's sponsor:
-------------------------------------------------------------------
Sign up today for a No Annual Fee DiscoverR Platinum Card and get.
0% Intro APR on Purchases & Balance Transfers for 8 Months, Up to
2% Cashback BonusR reward on your purchases & 100% fraud
protection.
http://click.topica.com/caadlRMb1dfltb7ukc8a/DiscoverCard
-------------------------------------------------------------------

Wow, Patrick, if I can't find the answer in there somewhere, then I'd
better turn in my metric wrenches and give up. Thanks!

Now that you mention the solenoid cap gasket, I have a sneaking
suspicion that I did not put a gasket back in there when I was
reassembling the solenoid after replacing the big contacts. I will
check that first, then look at tooth wear. Nothing else on this bike is
worn out ('cept the clutch acting up) so I'll be surprised if those
teeth are shot after only 35,000 miles....

That'll be next week, though. My wife and I are Centauro'ing over to
the coast tomorrow to spend the weekend and to confer, converse, and
otherwise hobnob with my brother Centauro owners, who are gathering from
all over the East Coast just to say hi and see who those guys are on the
other side of the keyboard...

Lannis

Patrick Hayes wrote:
 


Greg Bender wrote:
a longer throw (or, more precisely, a more foward pushing throw). But,
 if the starter gear is getting pushed all the way out every time, then I

 
 
think you are stuck with having a gear wear problem.

Lannis: I think I'm with Greg on this. And continuing your symptom
will only make matters worse.

Look at how the system operates. It must be a clear, two-step process.
When you hit the button, the relay and then the solenoid get
energized. The solenoid pulls its core inward, which pushes the starter

gear forward through a pivot lever. The starter motor is not yet
energized and does not yet spin.

As the pinion gear moves forward, the forward edge of its teeth are
supposed to impact against the rear edge of the ring gear teeth. Both
sets of teeth should be angled or tapered in some way to discourage a
direct, face-to-face tooth hit. At the point of impact, the pinion
should be forced to rock one way or the other to slide between mating
ring gear teeth.

As the teeth fully mesh and engage, the huge contacts down at the back
end of the solenoid inside its cap come into play. When these contacts
hit, the starter windings themselves become energized and the motor
starts to spin.

So, you have one of two problems.

First, is there some reason that the gear teeth do not embed? Has this
error caused the teeth to grind against each other, square off, and
exacerbate face-to-face locking? Can you get at the damaged teeth with
a dremel grinder and restore a pointed face condition?

Second, is the starter being energized to spin before the gears are
meshed? This is my suspicion. And here again we have two potential
problems. Somehow the starter is getting juice before the gears are
meshed.

First, has there been enough wear to the pivot and the various
mechanical points of the lever system so that it is not pushing the
pinion gear as far forward as it used to? Not sure how to repair that,
but you could remove the lever and have a little weld dab added to it to

restore original thrust dimension.

Second, has someone repaired, cleaned or replaced this solenoid? Was an

alternate substitute solenoid used? If it is the original solenoid, and

it was cleaned or repaired, was the original cap gasket saved or
reproduced? The physical position of the solenoid rear cap (and thus
its internal contacts) are critical to the design of this system. If
you move the cap slightly forward (by omitting the cap gasket) you allow

the starter contacts to come into play before the plunger thrust is
complete. If you use an alternate solenoid, the dimensions for thrust
and contact may not be completely accurate.

I would suggest a thorough tooth inspection and some lubrication of the
pinion shaft to get the gear sliding easier. You can run the solenoid
repeatedly on the floor with some test wire and observe its action.
Just be sure to disconnect the heavy starter lead so you don't energize
that spin or the motor with jump all over the place.

I would suggest a removal and very thorough inspection of the pivot
system and the fork face of the pivot against the pinion gear. Is there

some substantial wear and can it be improved or corrected?

I would suggest disassembly of the solenoid and the addition of a double

or triple thick gasket between the end cap and the solenoid body. By
adding gasket thickness here, you are moving the motor contacts aft and
delaying the instant point of energizing the starter. The plunger has
to go deeper before it makes the motor spin. Perhaps by stacking
gaskets, you can delay it long enough to get deeper tooth penetration
before spin. At any rate, what you have now is a rotary grinder and you

are damaging the face of the pinion and ring teeth. By doing so, you
are making the gear contact position worse as it respects the internal
solenoid contact position. You have to get tooth penetration BEFORE
spin. Doing the gasket stack might be enough to counteract the tooth
wear already in place.

One last thought. You might ignore ALL of the above and just inspect
the wiring at the starter and solenoid. You maybe haven't done
something to short this wiring in some way, or hooked it up incorrectly
so that the thrust action and the spin action are happening
simultaneously? That would be a case for failure for sure. You have to

separate these two functions in time and space. The starter relay ONLY
energizes the solenoid. It is the action of the solenoid which
energizes the starter windings. I'm trying to imagine how you could
hook up contacts incorrectly to get the motor spinning by the relay
circuit rather than by the solenoid circuit. Could happen I suppose.

Patrick Hayes
Fremont CA

Your free subscription is supported by today's sponsor:
-------------------------------------------------------------------
Is your PC running at 100%? Check your PC's health in 2 minutes!
http://click.topica.com/caadlAsb1dfltb7ukc8f/PCHealth Check
-------------------------------------------------------------------

Entire thread: